Winegrowers Supplies  -  tank stirrers (also known as rousers or agitators or mixers)

  A tank stirrer is an essential tool for professional winemaking; for sugar additions, blending, reducing CO2 etc.

Except where stated, all models have 380 volt (3-phase) motors, although some motors can be re-wired to run from 230 volt 3-phase.
3-phase stirrer motors require the supply to have 5 wires: 3 phases + neutral + earth; not just 4 wires (3P + N) as some 3 phase electricity supplies have.

The stainless steel shaft/propeller is withdrawn through the stainless steel pipe so that the pipe can be pushed through a Gr.37 Flap-valve (ZLK) and the collar tightened, the propeller/shaft is then pushed back into the tank and locked.

Some models are available with a fitting to go through a DIN40 or DIN50 ball-valve.

  IND:
       

IND-0: 230 Volts (1-phase) 0.37 kWatt, 1400 rpm, shaft 800 mm long / 15 mm diameter, 1224 Euros
         or 380 Volts (3-phase), 1200 Euros

IND-V0: variable speed model (with frequency converter), 380 Volts (3-phase), 0.37 kWatt, 2120 Euros

Available with interchangeable fittings: to go through a Gr.37 Flap-valve ('ZLK'), or a DIN40 (or DIN50) ball-valve; 180 Euros extra for each extra one if required.

On this mixer the stainless steel shaft is not pulled back through the motor. It is made of three parts:-
- a stainless steel fitting for a DIN40 (or DIN50) ball-valve or a Gr.37 Flap-valve, shown in the middle of the photo,
- the shaft and propeller, right side in photo,
- and the motor, which is connected after the other parts have been installed.

The disadvantage of using it with a DIN40/50 ball-valve is that it has to be installed in an empty tank, whereas with a Flap-valve it can be moved easily from tank to tank while the tanks are full.

  EN: 380 Volts (3-phase), 1400 rpm

   

with a fitting to go through a DIN40 or DIN50 ball-valve, or a Gr.37 Flap-valve ('ZLK').

EN-1: 0.75 kWatt, for tanks up to 35,000 litres, 1792 Euros

EN-2: for tanks up to 70,000 litres, 3440 Euros

Optional floor-standing adjustable height stand, in stainless steel, to support the weight of the motor, 276 Euros

   

  Kiesel, made in Germany, 380 Volts 3-phase:-

               wheeled stand
for use with an RG03 stirrer,
1992 Euros

Kiesel, 1400 rpm:-
RG0: 0.37 kWatt, 13 kilos, for tanks up to 15,000 litres, shaft 880 mm long, propellor diameter 150 mm, Euros
RG01: 0.75 kWatt, 18 kilos, for tanks up to 30,000 litres, shaft 900 mm long, propellor diameter 170 mm, Euros
RG02: 1.1 kWatt, 21 kilos, for tanks up to 50,000 litres, shaft 950 mm long, propellor diameter 190 mm, Euros
RG03: 2.2 kWatt, 33 kilos, for tanks up to 80,000 litres, shaft 1050 mm long, propellor diameter 200 mm, Euros

Kiesel variable speed models:-
RG0 FU: 0.37 kWatt, 250 to 1400 rpm, 13 kilos, for tanks up to 15,000 litres, Euros
RG01 FU: 0.75 kWatt, 250 to 1400 rpm, 18 kilos, for tanks up to 30,000 litres, Euros
RG02 FU: 1.1 kWatt, 250 to 1400 rpm, 22 kilos, for tanks up to 50,000 litres, Euros
RG03 FU: 2.2 kWatt, 350 to 1400 rpm, 33 kilos, for tanks up to 80,000 litres, 3343 Euros

Kiesel, 125 rpm:-
RG15: 0.75 kWatt, 18 kilos, for tanks up to 15,000 litres, Euros

Prices shown are exclusive of Vat.
Delivery will need to be charged at cost.

www.winegrowers.info