Winegrowers Supplies - tank mixers (also known as rousers or agitators)
A tank mixer is an essential tool for professional winemaking; for sugar additions, blending, reducing CO2 etc.
Except where stated, all models have 380 volt (3-phase) motors, although some motors can be re-wired to run from 230 volt 3-phase, or can be run via a simple 1-phase to 3-phase inverter. 3-phase mixer motors require the supply to have 5 wires: 3 phases + neutral + earth; not just 4 wires (3P + N) as some electricity supplies have.
The stainless steel shaft/propeller is withdrawn through the stainless steel pipe so that the pipe can be pushed through a Gr.37 Flap-valve ('ZLK') and the collar tightened, the propeller/shaft is then pushed back into the tank and locked.
Some models are available with a fitting to go through a DN40 or DN50 ball-valve.
IND-0: 230 Volts (1-phase) or 380 Volts (3-phase), 0.37 kWatt, 1400 rpm, shaft 800 mm long / 15 mm diameter, 950 Euros
IND-V0: variable speed model (with frequency converter), 380 Volts (3-phase), 0.37 kWatt, 1695 Euros
IND-1: for tanks up to 10,000 litres, 380 Volts (3-phase), 0.55 kWatt, 1400 rpm, 1190 Euros
IND-V1: for tanks up to 10,000 litres, variable speed model (with frequency converter), 230 Volts (3-phase) or 380 Volts (3-phase), 0.55 kWatt, 1970 Euros
IND-V2: for tanks up to 15,000 litres, variable speed model (with frequency converter), 230 Volts (3-phase) or 380 Volts (3-phase), 0.75 kWatt, 2200 Euros
Available with interchangeable fittings: to go through a Gr.37 Flap-valve ('ZLK'), or a DIN40 (or DIN50) ball-valve; 180 Euros extra for each if required
On this mixer the stainless steel shaft is not pulled back through the motor. It is made of three parts:-
- a stainless steel fitting for a DIN40 (or a DIN50) ball-valve or a Gr.37 Flap-valve, shown in the middle of the photo,
- the shaft and propeller, right side in photo,
- and the motor, which is connected after the other parts have been installed.
The disadvantage of using it with DIN40 ball-valves is that it has to be installed in an empty tank, whereas with Flap-valves it can be moved easily from tank to tank while the tanks are full.
Option: stainless steel 'leg', adjustable for height, for mounting on the motor, to support the weight, 155 Euros
or Kiesel, made in Germany, 380 Volts 3-phase:-
for use with an RG3 mixer, 1759 Euros
Kiesel, 1400 rpm:-
RG0: 0.37 kWatt, 13 kilos, for tanks up to 7,500 litres, 960 Euros
RG1: 0.75 kWatt, 18 kilos, for tanks up to 15,000 litres, 1169 Euros
RG2: 1.1 kWatt, 22 kilos, for tanks up to 25,000 litres, 1515 Euros
RG3: 3.0 kWatt, 33 kilos, for tanks up to 40,000 litres, 1795 Euros
Kiesel variable speed models, 250 to 1400 rpm:-
RG0 FU: 0.37 kWatt, 1400 rpm, 13 kilos, for tanks up to 7,500 litres, 1735 Euros
RG1 FU: 0.75 kWatt, 1400 rpm, 18 kilos, for tanks up to 15,000 litres, 2290 Euros
RG2 FU: 1.1 kWatt, 1400 rpm, 22 kilos, for tanks up to 25,000 litres, 2670 Euros
RG3 FU: 3.0 kWatt, 1400 rpm, 33 kilos, for tanks up to 40,000 litres, 3180 Euros
Kiesel, 125 rpm:-
RG15: 0.75 kWatt, 18 kilos, for tanks up to 7,500 litres, 1250 Euros
Prices shown are exclusive of Vat.
Delivery usually will need to be charged at cost.